Commonly referred to as a "4th Hand", the Park Tool Cable Stretcher pulls both gear and brake cables tight . It features one-hand operation with a thumb lock to hold the cable tight while your hand is removed to tighten pull-up bolts and nuts. 232 g.

The CBW-1 is an 8mm open and 10mm open end wrench. This small, nickel plated wrench can be used on brakes, derailleurs, etc. Hole in wrench allows easy hanging on peg board. 47 g.

The CBW-4 is a 9mm open and 11mm open end wrench. This small, nickel plated wrench can be used on brakes, derailleurs, etc. Hole allows easy hanging on peg board. 39 g.

The new CN-10 Cable and Housing Cutter is a shop quality cutter designed specifically for use on all bicycle cables and housing, including hard-to-cut index housing. The CN-10 has a built in crimper for cable end caps and a forming hole for reforming housing ends and housing ferrules. A wire latch holds the handles together when not in use. The CN-10 now features an internal spring, which makes crimping easier and faster. 378 g.

An updated version of the popular DAG-1, the new DAG-2 utilizes a longer measuring pointer, longer threaded stud and a longer, narrower alignment boss to fit a wider variety of bikes.

The DT-1 is designed to perfectly machine the face of each tab, removing paint and material to create a flat surface. The DT-1 works on 135mm rear frames with the "standard" 10mm axle dropouts, and 12mm through axles by using a spacer included with the kit. The DT-1 also works on front forks with 100mm axle width and a 9mm axle dropout, and with 20mm through axles by using a spacer included with the kit.

Specially designed, and precisely manufactured to gently adjust bent or damaged brake rotors. Each DT-2 features two different slot depths laser cut from high quality stainless steel.

Improperly aligned frame and fork dropouts can cause bent axles and quick release skewers, as well as tracking and shifting problems. The FFG-2 quickly, determines whether dropouts are aligned and parallel. If an error is detected, long handles and comfortable molded grips afford plenty of leverage for straightening. Works on frames and forks with dropout spacing up to 145mm.

The Handlebar Holder is designed to prevent the handlebar and front wheel from rotating when a bike is mounted in a Park Tool Repair Stand. Updated to fit handlebars with a diameter up to 32mm and oversized top tubes up to 50mm, the HBH-2 works on almost any road or mountain bike.

32mm head wrench and 15mm pedal wrench. Our popular and versatile Head Wrenches feature our proven "Y" head design and all headset wrench openings are laser cut to ensure a tight, accurate fit (Only headset sizes 30mm, 32mm, 36mm, and 40mm are laser sized). 232 g.

Park designed the perfect shop hammer! The HMR-2 is built with a fiberglass, reinforced shaft and a soft-touch rubber hand grip. A unique, two-sided head with both a steel and a rubber striking surface made specifically for bike shop use.

The new ISC-4 securely holds most bikes without clamping on any frame tube. To use, simply insert the ISC-4 into the frame's seat tube, tighten the knob, and clap into anyPark Tool Repair Stand. The ISC-4's hex-shaped shaft resists twisting while clamping in the stand. Works with a huge range of seat tube sizes anything with an outside diameter of 24mm to 32mm.

This bench top accessory keeps small parts accessible and all in one place. 6” (15cm) in diameter and featuring an extra strong magnet, the MB-1 is available only in World Famous Park Tool Blue.

World famous Park Tool quality is built into a great set of metric combination wrenches forged from chrome-vanadium steel. The 12-point box/open end wrenches range from 7 to 15mm.

Big and powerful, the PAW-12 is forged from carbon steel and chrome plated. Features a comfortable vinyl dipped handle. Jaws open to 36mm and feature a laser engraved measurement scale.

The unique, wedge-shaped PP-1 slides into a hydraulic disc brake caliper to pre-set the piston when replacing pads, aligning pads, and performing other service procedures. Makes hydraulic disc brake maintenance and repair faster and easier.

The new PW-4 Professional Pedal Wrench is designed for heavy shop use. Two 15mm wrench openings are oriented at 30 degree and 45 degree angles so the user can always achieve the best mechanical advantage, regardless of the pedal position. While strong, the PW-4 is thin enough to access all wrench flats. An extra long 14" handle provides the leverage to remove even the tightest pedals. 1.4 lbs

Designed to ensure a straight, clean cut on threadless forks, the SG-6 fits 1", 1-1/8" and 1-1/4" forks. A must for use with threadless fork systems. Simply slide the guide onto any threadless fork, clamp it down, and cut using the narrow cutting slot. Heat treated for long life. For threaded forks, use SG-5 Guide Set which cleans the threads after cutting. 434 g.

The use of Torx® (star-shaped) fittings on disc brakes, pedals, chainring bolts, etc. are becoming increasingly popular. The TWS-2 combines the wrench sizes currently being used on bicycle components (T7, T8, T10, T15, T20, T25, T30, and T40) in a convenient fold-up set. Composite handle is extremely strong (stronger than steel handles), comfortable to use and slip resistant. 168 g.